Articles

Semiempirical method of creation of generalized parameter-oriented model of mine hoist drum shell

User Rating:  / 0
PoorBest 

Authors:

K.S. Zabolotny, Dr. Sci. (Tech.), Professor, State Higher Educational Institution “National Mining University”, Professor of the Department of Mining Machinery and Engineering, Dnepropetrovsk, Ukraine

M.A. Rutkovskiy, State Higher Educational Institution “National Mining University”, Postgraduate Student, Research Fellow of the Department of Mining Machinery and Engineering, Dnepropetrovsk, Ukraine

Abstract:

Purpose. To develop the method of construction of a generalized parametric model of drum shell of a mining hoist based on its representation as a system with spatially lumped and distributed parameters.

Methodology. The developed method supposes that the object is described by a simplified model with experimentally defined coefficients which allow experimental and computational data to conform well.

Findings. The semiempirical method has been developed. According to it for calculation of bending of shaped shell of hoist drum an analytical model of an axisymmetric shell with equivalent mechanical properties involving coefficients of agreement with the empirical data should be used.

Originality. Dependence of the average flexural rigidity on the geometric parameters of the shell taking into account the reduction coefficient of rigidity has been established.

Practical value. The developed method allows reasonable selection of the parameters of the hoist drum, and its application in the design will create a competitive global market of lifting equipment with reduced weight, increased strength and durability. In comparison with previously used, this method several times will reduce the complexity of calculations of the strength of cylindrical drum winders.

References:

1. Заболотный К.С. Научное обоснование технических решений по повышению канатоемкости и уменьшению габаритов шахтных подъемных машин с цилиндрическими барабанами [Текст]: автореф. диссертации … д-ра техн. наук. / Константин Сергеевич Заболотный. – Днепропетровск, 1997. – 24 с.
Zabolotny, K.S. (1997), “Scientific substantiation of technical solutions to improve the rope capacity and reduce the size of mine hoist machines with cylindrical drums”, Abstract of Dr. Sci. (Tech.) dissertation, Dnepropetrovsk, Ukraine.

2. Безпалько Т.В. Оптимизация по канатоемкости проектных параметров барабанов шахтных подъемных машин [Текст]: автореф диссертации … канд. техн. наук. / Татьяна Витальевна Безпалько. – Днепропетровск, 2004. – 19 с.
Bezpalko, T.V. (2004), “Optimization of the rope-drum capacity design parameters of mine hoist machines”, Abstract of Cand. Sci. (Tech.) dissertation, Dnepropetrovsk, Ukraine.

3. Композиты на основе полимерных матриц и углеродно-силикатных нанонаполнителей. Квантово-механическое исследование механических свойств, прогнозирование эффекта усиления. [Текст] / Ю.Г. Яновский Е.А. Никитина, С.М. Никитин, Ю.Н. Карнет // Механика композиционных материалов и конструкций. – 2009.– №4. – Т. 15, – С. 566–589.
Yanovskiy, Yu.G., Nikitina, Ye.A., Nikitin, S.M. and Karnet, Yu.N. (2009), “Composites based on polymer matrices and the carbon-silicate nanofillers. Quantum-mechanical study of the mechanical properties, prediction of the effect of amplification”, Mekhanika kompozitsyonnykh materialov i konstruktsyi, Vol. 15, no.4. p. 566–589.

Files:
2012_4_zabolotny
Date 2013-08-13 Filesize 393.64 KB Download 1184

Visitors

6227373
Today
This Month
All days
1205
54050
6227373

Guest Book

If you have questions, comments or suggestions, you can write them in our "Guest Book"

Registration data

ISSN (print) 2071-2227,
ISSN (online) 2223-2362.
Journal was registered by Ministry of Justice of Ukraine.
Registration number КВ No.17742-6592PR dated April 27, 2011.

Contacts

D.Yavornytskyi ave.,19, pavilion 3, room 24-а, Dnipro, 49005
Tel.: +38 (056) 746 32 79.
e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.
You are here: Home